Genuine Ultraflex4x4 Toyota 80 Series Outer Lights Set kit. Hi/Lo KIT

  

ONE PAIR WITH HARNESS , INSTRUCTIONS, AND SCREWS. NO MORE CANDLE STICKS AND RF interference. Replaces PAR165x100,72066,72018,72022,72070,72080, H4651, H4656, H4666,8800,0551381,0552571,0551371,0552551. I make several products for the 80 Series.

All are suitable for PnP install. A halogen Cheap up grade. A Pair of outer lights Kit.

Do not be fooled by copies from these stores. Kapshop2015 essen_k yipenl3 oz_tool_it auto-bugs autosuperman2017.

Suite 80, 61 Series Toyota, RT132 Corona etc. UPGRADE NOW SUITE 24V Systems. Now comes with M4 screws. Under 2000 lm on low beam so no issues with QLD version of ADR13/00 (washers wipers and self leveling requirements).

If you are serious about driving and being able to see at night then these will make your job and your eyes. ADR Compliant with 46/00 and 76/00 Compliance is marked on the front face.

Feel free to jump on any Facebook forum and ask clients about their experience with this product. 4 x 6 Lights direct replacement of sealed beam and H4 no mucking around, Plug and Play. The relay kit is supplied for Toyota that use negative switching, and you can wire them for 24 Volts (replace the relays with 24V or specify in your order and I'll supply them) if required from the earth side battery of the 24V battery stack.

I'd rather you pay a little more and be super satisfied than. Be without lights and a rig for a whole night. The relay kit draws 5 Watts which is suitable for the high beam light to operate on the Toyotas.

In some cases you may need to replace the stock head lamp relays as the contacts may have arced and be in poor condition. Especially after running high wattage Halogens. Make sure you tell me Black or silver in the order and if you are 24V. Available in Black or Silver Front. I try and keep both in stock. Check out this demo video. These are built using the same components as the very popular 7 round 105W LED Head lights. 60 Watts LED (actual electrical watts are 31W) On high beam each so that is 120W per side and 240Watts total on High beam. (12,000 lm total 4 lights).

If you want those figure in "Halogen Power" on High beam.. It's about 840 Watts. All with only 12 amps current draw. On low beam they are 1800 lm (complies with ADR13/00).

The harness will have the low beam wires to the centre lights cut for legal reasons. But you can easily connect to your fog light switch. You "might be able to get away with" wiring up the second set low beam also you need to check your local state regulations.

If permitted in your state the low beam is a respectable 3600 lm for all 4 lights. It is legal to use the center low beams as "Fog Lights" on a switch. These have DRL (White Parker).

Yes these are Hi/Lo beam head lamps. 10-30 Volts suitable for 24V systems. They have + and - terminals. There is also a Discovery 1 conversion kit see photos. I was asked to find these lights by a few local 4x4 clubs searching for better lights that are Legal in NSW , VIC and QLD. After studying ARD46/00 and many exhaustive discussions with Chinese Manufacturing companies over several months I was able to Locate, modify and certify these lights for Australian useage.

I only sell things that I have personally used, and others have tested. That's how a 4x4 club works! Cleaning is via soft brush and mild soap. Certified by SAE, DOT, and E Mark and I have the proof of certification.

They are IP67 and can be submerged for 30 mins in 1.5M of water with and withstand high pressure water jet cleaning. LEGAL in ALL Australian States under. ADR 46/00 section 7.8. Listed else where be quick these are the first Legal high Wattage Lights available in Australia.

Come with integrated parker / DRL with Female spade connector (red wire) fitted and a H4 style 3 pin connector. That means great visibility under all conditions. The LEDs are the same "colour temperature" as a clear sky around Miday. I'm stoked at these lights so I thought I'd offer them to the general public after all the testing we've done.

Weight is 3.0 KG per set. NOTE: DO NOT block the breathers on these lights.

The frontal area is very large and 0.5 PSI is equal to 12 Kgs pushing the front cover off the assembly. The breathers are there to stop this from happening.

The heat generated causes pressure build up inside the light as the air expands. This WILL lead to moisture getting into the lights as the front seal is VERY important. If you have inadvertently done this then you can remove the front faceia using a 2.5mm Allan key and re-seal with black neutral cure silicone after drying with a hair drier on LOW setting. Here's the real clincher..

If you are not totally impressed.. New stock arriving every week. The item "Genuine Ultraflex4x4 Toyota 80 Series Outer Lights Set kit. Hi/Lo KIT" is in sale since Saturday, June 15, 2019. This item is in the category "Vehicle Parts & Accessories\Car & Truck Parts\Lights, Indicators\LED Lights".

The seller is "garret-au" and is located in Baulkham Hills, NSW. This item can be shipped worldwide.

1. Bulb Colour: 6000K
2. Manufacturer Part Number: UF 4x6" 60W B
3. To Fit: Headlight
4. Placement on Vehicle: Front
5. Brand: ULTRFLEX4x4
6. Type: LED
7. Bulb Size: 60
8. Warranty: 2 Year
9. Voltage: 10-30